Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You may locate that your garage door opener has been providing you issues, so you need to repair it. You can repair it by replacing a circuit board, a photo-eye sensing unit, the primary drive equipment, or the set-limit buttons. You can additionally inspect if the safety and security sensors are functioning appropriately.

Replacing a circuit board

Changing a circuit board for your garage door opener needs a couple of steps and also tools. Initially, you require to shut off the circuit breaker as well as detach any type of wires. Next off, open up the circuit board cover. This will aid you to detect the issue as well as establish if you need a brand-new board. Next off, eliminate the old board and also its wire connectors.

You can after that proceed to replace the motherboard. The substitute procedure is easy as well as takes about 10 minutes. A new circuit board will set you back about $80. To safeguard your new circuit board from power surges, you can purchase a rise guard.

Changing a photo-eye sensor

Changing a photo-eye sensor can be a rather simple task. Initially, remove the sensing unit from the door and make certain it is located correctly. If the sensor is angled by any means, it may not be getting the appropriate signal, which might be triggering the blinking lights. If you observe that the photo-eyes run out positioning, you might require to have actually a technician come as well as take care of the issue.

The photo-eye sensing unit contains two pieces that install on the outside of the door tracks and also toward the floor. The picture eyes will have a tiny LED light as well as need to be solid in shade. If the light is blinking, its most likely the photo-eye is defective and will require to be changed.

Changing a major drive gear

To change a garage door opener main drive equipment, begin by removing the cap from the chain pulley. Next off, eliminate the two screws holding the drive gear to the gear assembly. Currently, you can loosen the three tension pins. Squeeze them from both sides and afterwards remove them. After that, separate the three cords from the garage door opener motor. These cords should be white, red, and also blue.

Once you have actually gotten rid of the old equipment, install a brand-new one. Make certain to oil it well. Place the brand-new gear into the shaft, making sure to align the mounting holes. Ensure the equipment and also gear assembly are positioned properly to ensure smooth operation. Next, utilize a hammer and a nail to drive a pin right into the brand-new gear.

Adjusting the set-limit switches

The first thing you must do if your garage door is not working properly is to check the set-limit buttons. You might require to readjust them so that the door shuts earlier or quits before it gets to the floor. You can examine this by checking out your garage doors handbook or online.

To change the set-limit switches, youll require a screwdriver or socket. Adjust the handle clockwise or counterclockwise until the door goes up as well as stops, or reduces its range. To check for appropriate traveling range, determine the space from all-time low of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Main St Ste 105, Keller, TX 76248, USA

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *


Back To Top